Led Traffic Light and Traffic Solution Supplier.  sales3@traffic-lights.cn

44 Output Networking Intelligent Traffic Signal Controller With Cabinet



Housing Material:

Cold-rolled Steel 

Working Voltage:





CE(LVD, EMC) , EN12368, ISO9001, ISO14001, IP55

  • technical
  • picture
  • contact

Product Functions and Technical Features:

1.Built-in central control system to ensure work stability.
2.Easy for maintenance and function extension by modular design.
3.Input  AC110V and AC220V, Can be changed by the switch.
4.Adopt RS-232 or LAN port to communicate with upper computer.
5.2*48 work periods for workday and holiday setting.
6.32 working menus used for any period(among 1~30 numbers customs can set it by themselves).
7.The flashing state, frequency and time of each green signal light can be setup or adjusted.
8.Yellow flashing or close the signal can be setup at night.
9.Can modify the current pace of running time in the running state immediately.
10.Full red, yellow flashing, step by step manual,jump in the manual,remote manual function(optional).
11.Be equipped with the hardware fault testing function(Red Light fails,Green lights up test),down grade to Yellow flash status and cut down the Red&Green light power supply when the fault happens.(Optional)
12.The output part adopts zero-test technology,Change of state is zero state switch in communication,Make the drive more safe and reliable.
13.Each output all the way with independent lightning protection circuit.
14.Installation testing capabilities,can test to confirm installation correctness for each lamp when installation at intersection.
15.The clients can set up 30 menu to be backup and recovery .
16.The setup software can operation on the computer offline,Project data can be stored on the computer and can be copied.

Technical specifications:

ItemTechnical Parameter
Executive StandardGB25280-2010
Working VoltageAC110V/220V±20%(changed by switch)
Working Frequency47Hz~63Hz
No-load power≤15W
Each Output Drive Capability2A
The whole controller rated load power2200W
Surge current in each way≥100A
The largest output channel independently44
The largest output way independently16
Working menus32
Can be setup menus number30
The largest number of each menus32
The largest number of timers in each day24
Running time in each step1~255S
Full red transition time 0~5S
Yellow light transition time0~9S
Green flashing time0~9S
Working Temperature-40℃~+80℃
Relative Humidity<98%
Setting Plan Saving Time(The electricity was turned off)10 years
Time ErrorYear error<2.5 minutes(in the condition of 25±1℃)
Inner Cabinet Dimension1250*630*500mm
Outer Cabinet Dimension472.6*215.3*280mm

Special Function Operations:


Introduction to the function of side-door switches and buttons
When the knob switch to 1,the outputs will be tumed to full red.

When the knob switch to 1,the outputs will be tumed to yellow flashing.
When the knob switch to 3 is Automaticl state.
When the knob switch to 4 is manually state.
Introduction to the functions of combination keys
Under the manually state and no green light conflict,press the directions button on the side door,singlebuttom or 2 directions keys(The two buttons are less 200ms apart),and set to work about release programs immediately.ex,single direction left tunm,go straight or south and north go straight.
Step button function introduction
In manual mode,press the step button each time,the step will be executed at once.

Remote controller operation introduction ( notes: it is as per customers requirements to match)
1, The picture shows the remote controller as the right picture, the effective distance is about200m.
2, The left black parts is power supply for remote controller.
3, The Capitals of ABCD on the remote controller was corresponding function as below,

FunctionManuallyFull redYellow flashingExit

The Common faults and solutions for controller

ItemFailure phenomenaSolutions scheme
1The controller doesn’t work ,and has no power .The fuse may be cut off. Users need to use a fuse of5Aor main fuse of10Ato change it. Main fuse is in the power socket.
2The signal lights in the road intersection keep flashing amber and it is because of setting.The reason maybe is the phasis setting, and there are have green conflicts ( the panel green conflict indicated light). You need to reset the phasis programs again.

Signal Controller Wiring Diagram
network signal controller

network traffic controller

network traffic controller

The traffic intersection

Quality assurance


Send Message to Us
If you have any question,Please Write it down to contact us now.
led traffic light
You can contact us in the following ways

Shenzhen: 4F North, Building C, Fenda High-tech Park, Xixiang Street, Bao'an District, Shenzhen, China. 518126

Yangzhou: No 209, Tongxin East Rode, Wu'an town, Gaoyou, Yangzhou, Jiangsu, China. 225600




  • Home
  • Phone
  • Message
  • © 2005-2019 Shenzhen Fama Intelligent Equipment CO.,Ltd / Yangzhou Fama  Copyright